Suggestion 1: Smoking Enhanced Leaf
The enhanced leaf can be smoked in just about any way you can think of. It works fine in a
bong or pipe, however I find a bong to add too much ‘punch’ to the experience. A joint works
a treat but is a little too wasteful at times. Personally, I find the pipe method to work perfectly,
and in particular, a glass pipe with a long travel which cools the smoke much more than the
standard metal pipes.
One like this will work fine:
TIPS!
�� Start with a small cone so you can
gauge the strength and intensity of the
product
�� Don’t start inhaling fully until the entire
cone is glowing
�� Inhale slowly; the smoke is quite harsh
and coughing while tripping is strange
�� If the smoke gets too harsh, hold your
breath until your throat calms, then
continue
�� DON’T EXHALE BETWEEN TOKES!
The number one key to achieving the
break through is to get the whole cone
in ONE LUNGFUL
25
Suggestion 2: Smoking Crystal
As the extracted DMT is a freebase, it can be smoked as is. Some people may find it a little
too harsh for their liking, and others may find the taste offensive. Personally, I love the smell
and the taste, but each to their own. 50-60mg of freebase DMT makes for a good hit, but you
may wish to start with lower doses like 30mg to get used to the smoke and the effect.
There are several ways you could smoke the crystal, but the fact is you do need to get a large
volume of smoke in a single lungful to really achieve the DMT effect. Vaporising on foil and
sucking through a straw isn’t going to cut it!
This is a standard glass pipe used for smoking crystal.
It’s a good design that would allow you to vaporise the
DMT rapidly without losing much, if any of the smoke.
Weigh your dose and put it in the bulb at the end.
Vaporise it with a jet lighter and take in as much of the
smoke as you can in as few tokes as possible.
Remember to hold the smoke for as long as possible!
Alternatively, there’s…
“The Machine”
Featured in The Entheogen Review, Volume XII, No 1
The Machine is capable of holding many doses, so you can load the device and take with.
There is little to no loss with this device, and for some reason, the smoke it produces is
significantly smoother than conventional crystal pipes like the one pictured above.
To make The Machine, you will need the
following items:
- A glass, single serving alcohol bottle of a
similar shape to the one pictured here. The
long straight neck is an important feature
- Some very coarse steel wool
- A 6mm drill bit designed for drilling glass
The first step is to drill a hole in the bottom of
the bottle. Patience is the key; don’t drill too
fast and don’t use too much pressure. This
took about half an hour
If you find that the drill bit is slipping, you can
try placing a small piece of masking tape where
you want the hole and then drilling
26
Once you have drilled the hole, place a
small amount of steel wool firmly into the
neck of the bottle as shown here
The Machine is now ready for use.
To charge the device, one or more good
doses are placed directly on top of the
steel wool at the mouth of the bottle. The
neck of the bottle is then gently heated just
enough for the crystal to melt and lacquer
the steel wool.
At this point The Machine is charged and
can be used now, or later. It’s a good idea
to save the bottle lid if you plan on carrying
the device around while it’s charged.
To charge the device with multiple doses,
drop a large quantity of crystal through the
broken hole onto the steel wool plug. The
neck is then heated until all the crystal
melts into the steel wool.
To use The Machine, point the neck downwards and heat the steel wool from below with a jet
lighter while slowly inhaling through the hole in the bottom. Practice makes perfect and you
will quickly learn the technique required to effectively and efficiently use The Machine to
deliver the dose you require.
Suggestion 3: Using Salts
Salts of DMT, in particular DMT Fumarate which you perhaps made in Part 3: Salting, have
different properties to freebase DMT. Foremost, salts are water soluble, allowing for
alternative methods of ingestion.
Because our mucous membranes are mostly water based, a salt form of DMT will dissolve
into them more freely than a freebase would, hence allowing the user to achieve the DMT
experience by snorting. If you’ve ever tried this with freebase DMT then you’d know that the
bad far outweighs the good. On the other hand, DMT Fumarate is a pleasure to insufflate.
The experience is quite like a shortened ayahuasca journey in the sense that it is longer and
slower than a smoked experience. A higher dose is needed to achieve effects however, so I
recommend you start with 100mg and tune to your liking from there. Personally, 150mg to
200mg is where it gets interesting. Preloading with MAOI (explained in
Suggestion 4:
Pharmahuasca) is a way in which you can and further enhance and potentiate the
experience.
Some of you may wish to take your experimentation further than others and look into IV or IM
injection routes. I am impartial in this area and am merely here to present you with
information. I will say that it can be done safely, however you must put specific measures in
place to ensure this. This would mean recrystallising the freebase multiple times until no
insolubility remains, and only then proceeding to make the Fumarate salt.
Doses are in the area of 0.5mg of DMT Fumarate per Kg of body weight for IV, and 1mg/Kg
for IM. Dissolve the dose in 0.3 mL of saline solution and draw it through a 0.22 micron inline
filter.
What you choose to do with the salt is up to you, but if you do wish to try the latter then
please do so with the utmost care and respect for your body.
![:\](https://bluelight.org/xf/BL_Images/Orig_Emoji/wrygrin.gif "wry grin :\")
) and showed similar symptoms of anxiety? or have there been some obvious hypersensitivity like reactions?