amphetamine extraction from adderall
.I'm not sure how to do the xr extraction as I've never tried it but here is how to extract amphetamine hcl from adderall ir.
Depending on your knowledge, perhaps you can use this as a starting point and go from there
Amphetamine hydrochloride, which is Amphetamine in its powdered form, is primarily produced from the Elements of the Periodic Table, which by some chance/luck spill into each other at the right time under the right conditions, somehow/someway in different glass peaces ending in the finished Amphetamine Salt (We mad scientist call this a act of God)...... Amphetamine is a chiral compound. The racemic mixture can be divided into its optical antipodes: levo- and dextro-amphetamine. Amphetamine is the parent compound of its own structural class, comprising a broad range of psychoactive derivatives, e.g., MDMA (Ecstasy) and the N-methylated form, methamphetamine. Amphetamine is a homologue of phenethylamine.
List of supplys/chemicals needed for Amphetamine Salt Extraction From Adderall IR-
-Adderall IR Pills
-Sodium Bicarbonate:Local Store, Chemical Supply.
-Ammonium Hydroxide (Pure ammonia solution 27%):Chemical Supply Store.
-Potassium salt:Chemical Supply Store
-Petroleum Ether:Chemical Supply Store
-Hydrochloric Acid (High% for best results/easiest procedure):Chemical Supply Store.
-PH papers (Litmus or Phenaphthazine-base/acidic needed):Chemical Supply Store, Pharmacy.
-Distilled Water
-Filter Papers (Lab grade prefered):Chemical Supply Store.
-(1)4"to 6" Glass Vial with chemical type Poly-Seal screw on top (For use as shaker vial and reaction vessel):Chemical Supply Store
-(1)Large glass or porcelain watch-glass (8"to 12" for ether evaporation)
-(1)Boiling Flask-Florence Flasks (Flask, boiling, flat bottom, 250ml, borosilicate glass works best):Chemical Supply Store
-(1)Cork Or Rubber Stoppers for Boiling Flasks
-(6)Pyrex Lab Glass Beakers:Chemical Supply Store.
-(2)Standard Precision Glass Eyedroppers (for use with hydroxide and also HCl solutions,make sure to mark each dropper)
-(1)Large (3 to 5cc) glass or polyethylene precision dropper (for use with ether):drug store, chemical supply or surgical supply.
-(1)Large Boiling Pot for making the FIZZLE.
Procedure #1-Amphetamine Free-basing-
Step 1-add pulverized Adderall IR pills+baking-soda add 1" of water(high) placed inside of jar. Mix around good.
Step 2-Check ph, remember you want closest to 7.2 and no more then 7.7 (Add either more Adderall or baking-soda depending on ph).
Step 3-Taking care not to break the jar or burn your hands, place the loosely capped flat bottom Boiling Flask in a shallow hot water bath and bring the water to a low boil.
Step 4-Let stand for a few minutes (2-4 approximately) until all milkiness has given way to the formation of particles or chunks.
Step 5-Continue the water bath while tilting the jar at a 45 degree angle and slowly rotating or swirling the jar in such a way as to cause the chunks of partially melted base to form or a few larger pieces.
Step 6-(Note-before Adderall Free-Base can be removed from the jar and rinsed, the jar and contents must be thoroughly cooled. Care must be taken not to break the jar by exposure to rapid, radical changes of temperature.)
Step 7-place chunks in a filter paper rinse with water about 4 times changing filter after second rinse.
Procedure #2-Ether Extraction-
Step 1-Using the large dropper, add about 1 1/2 inches of ether to the vial containing the free-base suspension. Cap tightly and shake furiously for at least one minute. The particles of free-base will dissolve into the ether. If not, continue shaking until it appears that no more particles are dissolving. Let the vial stand until there is no more bubbling effect, and the ether has formed a definite layer above the basing solution. Open away from eyes. Use the smallest amount of ether possible to absorb the free-base in the vial. If there are still remaining particles of free-base in the vial which did not dissolve, it is an indication that a little more ether is necessary to dissolve the total volume of base. (Note-This can be corrected as in Step-4 below).
Step 2-Using the large dropper, carefully draw off the ether from the vial. Holding the dropper up to a light source, you should be able to see if there is a layer of basing solution under the ether/base column in the dropper. Make certain not to leave even one drop of basing solution in the dropper.
Step 3-Carefully hold the dropper upright over the center of the large watch glass and slowly squirt the ether/base solution onto the glass. Repeat until there is no more ether in the vial.
Step 4-If you get near the point at which no ether remains in the vial and there are remaining particles of free-base in the vial, add a little more ether (1/4 to 1/2 inch) and shake furiously until all the particles dissolve, then repeat steps 2 and 3.
Step 5-Let the watch glass stand until the ether thoroughly evaporates. Some people like to help this process along by gently blowing on the surface to speed evaporation. When the center of the watch glass doesn't feel cold to the touch from underneath, the free-base is ready to be scraped off with a razor blade and smoked. If the ether is not allowed to evaporate thoroughly, the free-base will ignite when torched/smoked.
Procedure #3-Amphetamine-Base reverse-engineered back to a chemical hydrochloride state-
Step 1-Dissolve Amphetamine-Base in hydrochloric acid and water.
Step 2-Add potassium salt, which causes undesirable substances to separate from the mixture.
Step 3-Ammonia is added to the remaining solution, powder Amphetamine precipitates out, and is then removed and dried. (95% + YIELDS AMP HCI)
(Note-While the active ingredient in powder Amphetamine -- Amphetamine alkaloid -- does not differ from that in Amphetamine-Base, the salt that is added during this process renders Amphetamine hydrochloride unsmokable. However, the salt renders the Amphetamine hci: i.e., readily dissolvable in water)
