brimz
Bluelighter
very easy would u like instructions ? no ?
Well ur getting them anyway =p lol
1ltr clear plastic bottle lid replaced with copper pipe work including an 90 degree bend gauze is forced down to the point of bend where pipe is in position where stuff could get through in to bottle by mistake then more copper pipe joint work added with spontex but the pipework must be perfect fit for top of bottle so they can be attached easily , then a special tape is used to ensure no loss of suction , the tape is black yet not sticky how it works is u pull of the white sort of film and wrap around bottle ans copper pipe head u have made and the more tighter you pull ans wrap the more this stuff wants to grip to the item as it possible can hence ensuring no loss of suction from other end that we will now discuss.
You want to get a good quality kind of AIR pipe so you can suck the smoke through it a bit like this http://2.bp.blogspot.com/_dytG60JC2...AB0o/O0BJpuTwZzw/s400/aquarium-air-pipe-0.jpg but usually better more sturdy than floppy , u make a small hole just big enough for it alone to go through but still there will be suction loss so u take a brown piece of paper and wrap it round the air pipe and feed it through the hole in the bottle and as pull backwards slowly the brown paper will start to ripple and cling to the air pipe but as its gathering and gathering the hole for the air pipe is getting less and less open space around it until the air pipe and the brown paper is scrunched so perfectly in this hole in then you can tell that there is no gap around the circumference you now only have a 1 way air system pipe starting with the head that has the safety gauze and is so damn secure no one is pulling it off the bottle and remember there was a 90 degree piece added so you can hold the bottle length wise and then the opening of the head with spontex which alot of people use in pipes for smoke white AKA crack.
Next we add a very small hole to the bottle which when first smoking we cover with our thumb so make sure you put it in a good place where your thumb will end up when holding it to smoke , this is called the clearing hole .. only about 4mm big .
Your pipe is ready .
Next take your tooter and put how ever much your going to add to you pipe on to your chasing foil be it a £5 bit to a £40 bit (yes its been done) .. now just smoke this enough to turn it in to a beatle now make sure u have some of the spontex which btw you held away from ur self with pliers or on the end of something and burn it so the silver coating has burnt off and u aint smoking it .. so yes make sure your pipe head is at least half depth full of that and then peel off the beatle and break in to pieces cover with a thin 2nd layer of pre burned spontex and do the same OR just put the entire beatle in as a whole but on top of as much burned spontex as u can sp it doesnt just burn in to an liquid and stick to the copper pipe sides and hence good reason for gauze further deeper in to the pipe head but either way u gonna get one hell of a smoke and after many use u can cut off that special tension tape take out the parts and scrape the head and wow you get some amount of a smoke , beats a tooter any day .. lets continue when u start ton smoke keep the clearer hole covered and smoke like any other pipe and watch as the pipe fills and fills with smoke (each method will fill differently) once the pipe is full and still burning the beatle have a poke around the head to loosen it up so you get at parts of the beatle u may missed then smoke again one more draw an then the 2nd draw take that thumb off the clearing hole and boy phewww you going to get all that smoke thats been building up each time you take a suck on it and hold it all in just like u have been with every other draw u took but this one is more special he he and believe me your going to itch even if u ar used to it like me
Very intresting ROA u got their mate.
TBH i think i would be in tears by the time , i'd done all that , i'm not known 4 my patience when in posesion of Heroin .
Straight on the foil or in the Spoon 4 me .
It sounds a bit like a glorified Crack pipe tbh.