Tortured_Genius
Greenlighter
- Joined
- Sep 21, 2025
- Messages
- 1
This is my copy/paste post from Reddit where I would surely get no answers and all judgmental commentary.
I have been digging and I have read that it's possible and kinda convoluted and tricky but it can be done.
My tolerance is too high, my prescriptions are running out 1.5 weeks prior to refill date, 3x 30mg of serax, 3x 1mg klonopin and 3x 1mg xanax is my daily prescription.
I will be careful, and Responsible, I just need information and no judgement.
From my research I know I need Propylene Glycol USP 99.9% Pure, 100% Pure Vegetable Glycerin and vinegar?
Can anyone message me or give me some information on how to do this. I need this. I know what I'm doing with drugs, I've been fucking with benzos for more of my life than not. I am a disciplined, strong-willed person and I am in control. Which as I type this makes it seem like I'm not.
Again, I need this. anyone is welcome to message me intel of the process, ingredients, or other personal experience.
If not here, where can I find the information, at the very least.
I do not have access to IV benzos or I would just get liquid form.
Here is a copypasta of some very vague instructions, it's the only intel I could really find after sifting through hundreds of "drug abuse help" adverts.
"Yes, you can inject xanax actually. Xanax is not soluble in water, so water is out of question. its only used to dilute your solution to make it less acidic for your viens. Alprazolam is soluble is Propylene Glycol, Vegetable Gylcerin, and acetic acid aka vinegar. so what you do is if you have a 2mg bar you crush down .5 or 1mg and add it to your spoon or what ever. drop a few drops of PG onto the powder, then squirt about 50 units of vinegar onto the crushed pill and PG. mix it up and then let it sit for a couple minutes, then apply a small amount of heat to weaken or break the fillers binders. then cotton or microfilter your solution. get every last bit of liquid out of your mixture. you will probably have 50 units or maybe loss 10 units. once again then crush up another .5 or 1mg and again add a few drops of PG. then squirt your 1mg solution onto the PG pill mixture and maybe add another 10units of vinegar. mix, let it sit, then again add some heat. then once again filter it up again. then clean your spoon or what ever you used, then get a different new, newer syringe to re filter up for the last time.. when you do this, it turns out to be extremely strong. it gives you a nice strong rush, which tapers out to a 100% bio available buzz which lasts easily one to two hours longer. Just be extremely careful because it can be quit dangerous if you miss or over do it. just be moderate!"
I have been digging and I have read that it's possible and kinda convoluted and tricky but it can be done.
My tolerance is too high, my prescriptions are running out 1.5 weeks prior to refill date, 3x 30mg of serax, 3x 1mg klonopin and 3x 1mg xanax is my daily prescription.
I will be careful, and Responsible, I just need information and no judgement.
From my research I know I need Propylene Glycol USP 99.9% Pure, 100% Pure Vegetable Glycerin and vinegar?
Can anyone message me or give me some information on how to do this. I need this. I know what I'm doing with drugs, I've been fucking with benzos for more of my life than not. I am a disciplined, strong-willed person and I am in control. Which as I type this makes it seem like I'm not.
Again, I need this. anyone is welcome to message me intel of the process, ingredients, or other personal experience.
If not here, where can I find the information, at the very least.
I do not have access to IV benzos or I would just get liquid form.
Here is a copypasta of some very vague instructions, it's the only intel I could really find after sifting through hundreds of "drug abuse help" adverts.
"Yes, you can inject xanax actually. Xanax is not soluble in water, so water is out of question. its only used to dilute your solution to make it less acidic for your viens. Alprazolam is soluble is Propylene Glycol, Vegetable Gylcerin, and acetic acid aka vinegar. so what you do is if you have a 2mg bar you crush down .5 or 1mg and add it to your spoon or what ever. drop a few drops of PG onto the powder, then squirt about 50 units of vinegar onto the crushed pill and PG. mix it up and then let it sit for a couple minutes, then apply a small amount of heat to weaken or break the fillers binders. then cotton or microfilter your solution. get every last bit of liquid out of your mixture. you will probably have 50 units or maybe loss 10 units. once again then crush up another .5 or 1mg and again add a few drops of PG. then squirt your 1mg solution onto the PG pill mixture and maybe add another 10units of vinegar. mix, let it sit, then again add some heat. then once again filter it up again. then clean your spoon or what ever you used, then get a different new, newer syringe to re filter up for the last time.. when you do this, it turns out to be extremely strong. it gives you a nice strong rush, which tapers out to a 100% bio available buzz which lasts easily one to two hours longer. Just be extremely careful because it can be quit dangerous if you miss or over do it. just be moderate!"
