Hi there, first of all, thanks for the interest. I am newly diving into DMT extraction and have some general questions for either people who are experienced in extractions or Chemistry-savvy.
Please jump in on as many as you like:
1.) Emulsion: Why is this a bad thing? Is it only because it takes longer to fully settle? I am extracting from MHRB using a standard tek, and on my first attempt I just ended up shaking the jar instead of rolling the naphtha through the mixture. There was some bubbling which I found settled out perfectly within 10 or 20 min into perfect clear layers. Is separation the only reason shaking or an emulsion is bad?
2.) Are the draws supposed to be cloudy? Mine are almost perfectly clear with the tiniest tint of yellow which can barely be noticed, but clear nonetheless.
3.) What is the ideal length of time to roll hot naphtha through the mixture? And same question for emulsion, may I just shake it if it seems to be settling out perfectly afterwards?
4.) What temperature should the naphtha be at going into the mixture?
5.) What are the benefits/drawbacks of heating the basified root bark mixture before doing pulls?
6.) If I desired to do a wash with soda ash/distilled water, especially when the naphtha is very clear, is there any problem with me using food colouring to the water to make the separation line more distinct and make sure I am only pulling pure naphtha? Any reason this would not be advised?
7.) When I do my pulls, can they go straight into the freezer, or is it advisable that I cool them in the fridge first to avoid condensation?
8.) Glassware? I bought some cheap borosilicate glass beakers, flasks, graduated cylinder, pipettes, even a little separatory funnel, etc on eBay. What is the best way to clean glass you'd use in extraction so there's no residue? I have been using soap and water, then a good hot water rinse, spraying vinegar in it once dry, washing it off with hot water, then putting it in the oven for a few minutes. Should I use alcohol? Any problem with what I'm doing for what I need?
EDIT:
9.) What is the idea length of time to leave the MHRB soaking in the basified mixture? Minimum? Maximum (if any, is a week ok?)?
Thanks to any who answer.
-GA
Please jump in on as many as you like:
1.) Emulsion: Why is this a bad thing? Is it only because it takes longer to fully settle? I am extracting from MHRB using a standard tek, and on my first attempt I just ended up shaking the jar instead of rolling the naphtha through the mixture. There was some bubbling which I found settled out perfectly within 10 or 20 min into perfect clear layers. Is separation the only reason shaking or an emulsion is bad?
2.) Are the draws supposed to be cloudy? Mine are almost perfectly clear with the tiniest tint of yellow which can barely be noticed, but clear nonetheless.
3.) What is the ideal length of time to roll hot naphtha through the mixture? And same question for emulsion, may I just shake it if it seems to be settling out perfectly afterwards?
4.) What temperature should the naphtha be at going into the mixture?
5.) What are the benefits/drawbacks of heating the basified root bark mixture before doing pulls?
6.) If I desired to do a wash with soda ash/distilled water, especially when the naphtha is very clear, is there any problem with me using food colouring to the water to make the separation line more distinct and make sure I am only pulling pure naphtha? Any reason this would not be advised?
7.) When I do my pulls, can they go straight into the freezer, or is it advisable that I cool them in the fridge first to avoid condensation?
8.) Glassware? I bought some cheap borosilicate glass beakers, flasks, graduated cylinder, pipettes, even a little separatory funnel, etc on eBay. What is the best way to clean glass you'd use in extraction so there's no residue? I have been using soap and water, then a good hot water rinse, spraying vinegar in it once dry, washing it off with hot water, then putting it in the oven for a few minutes. Should I use alcohol? Any problem with what I'm doing for what I need?
EDIT:
9.) What is the idea length of time to leave the MHRB soaking in the basified mixture? Minimum? Maximum (if any, is a week ok?)?
Thanks to any who answer.
-GA
Last edited: