Im looking for help in safely creating a safer injectable formual than what Ive been doing. I have read through quite a few threads on here including that 32page + one right now on safe IV prep. I assume it does not matter whether you shoot it IM or IV when making it. I have never done IV (besides in the hospital) however I have gotten into IM dilaudid recently and would like to do everything possible to make this as safe as possible. I have a high tolerance so before anyone asks its pretty high. I took a IM shot w 8x8mg dillys this am and it was nothign much for me.
So if anyone can help direct me how best to do this i would greatly appreciate it. I will list what all I have below.
unlimited BA water (sterile water)
tons of 20g 3ml needle syringe combo, every size screw on tip to chang to anywhere between 25-30g tips.
1 cc 30g 5/16 diabetic pins.
5-10ml syringes.
Syringe filters: PTFE .22um/13mm syringe filters (100ct) & PES .22um 33mm hydrophillic filters (10) thsese ones look alot bigger like theyd be for bigger batches.
8mg IR Dilaudid pills (55 left and a cpl hundred more on the way).
I would like to make enough where I only need to make it once a day or once every cpl days. I don't know if that's possible though as I've seen people say the filters clog when you try to make too much at once?
I plan on shooting this IM. I have never done it IV though Im interested in trying if I could use less than when I do IM. Could one likely use a lot less going IV over IM? Would 2mg IV be a good starting place or is that too low with a tolerance like mine?
I was grinding the pills into powder and backloading them in a syringe before drawing BA water into it and letting it dissolve. I then put a filter on it and pushed it into a vial. I drew it out of the vial in a new syringe and IM'd it. I only made it for injecting right then so i never cared how much water i used. I dont know if more water will make it filter easier as its more diluted but I would like to create a formula so I know that 1ml solution = example 24mg or any other variable mg/ml dilaudid when I create this going forward. Does anyone have a reciept they can share to make a sterile injectable formula?
As always, I appreciate your time and direction very much.
So if anyone can help direct me how best to do this i would greatly appreciate it. I will list what all I have below.
unlimited BA water (sterile water)
tons of 20g 3ml needle syringe combo, every size screw on tip to chang to anywhere between 25-30g tips.
1 cc 30g 5/16 diabetic pins.
5-10ml syringes.
Syringe filters: PTFE .22um/13mm syringe filters (100ct) & PES .22um 33mm hydrophillic filters (10) thsese ones look alot bigger like theyd be for bigger batches.
8mg IR Dilaudid pills (55 left and a cpl hundred more on the way).
I would like to make enough where I only need to make it once a day or once every cpl days. I don't know if that's possible though as I've seen people say the filters clog when you try to make too much at once?
I plan on shooting this IM. I have never done it IV though Im interested in trying if I could use less than when I do IM. Could one likely use a lot less going IV over IM? Would 2mg IV be a good starting place or is that too low with a tolerance like mine?
I was grinding the pills into powder and backloading them in a syringe before drawing BA water into it and letting it dissolve. I then put a filter on it and pushed it into a vial. I drew it out of the vial in a new syringe and IM'd it. I only made it for injecting right then so i never cared how much water i used. I dont know if more water will make it filter easier as its more diluted but I would like to create a formula so I know that 1ml solution = example 24mg or any other variable mg/ml dilaudid when I create this going forward. Does anyone have a reciept they can share to make a sterile injectable formula?
As always, I appreciate your time and direction very much.