• 💊 OTHER DRUGS 💊 Welcome Guest
    Posting Rules Bluelight Rules
    Notable Threads 1 Notable Threads 2
    Dangerous Combos Addiction Support
    Emergency Services Benzo Guide v.1
    Addiction Stories Scary Case Studies
    Biology, Pharmacology & Drugs 101
  • Select Your Topic Then Scroll Down
    Alcohol Bupe Benzos
    Cocaine Heroin Opioids
    RCs Stimulants Misc
    Harm Reduction All Topics Gabapentinoids
    Tired of your habit? Struggling to cope?
    Want to regain control or get sober?
    Visit our Recovery Support Forums

RCs Cannabinoids that work in e-cigs

Y

Youpi

Bluelighter
Joined
Apr 30, 2009
Messages
53
Hello there,

I read on here that people succeed at vaping cannabinoids in e-cigs.

I would like to know what compounds was used as well as the solvent and the TEK to smoke it in an e-cigs.

Long time ago I had tried with a solution of UR-144 in propylene glycol but I wasn't getting any effect of it, was also a pain to get it to fully dissolve, that may also have been my problem.
At one point I even swallowed what must have been 200+mg in the propylene glycol and had no effect, it must not be active orally or that was my massive tolerance.

Now, I would like to try again, preferably following someone's recipe.

So can anyone tell me his experience about vaping cannabinoids in e-cigs ?

Thx
 
Don't focus on the e-cig part, I own two, one of them I can set the voltage so I'm quite set up.
I would like to know what cannabinoid is used, I guess it has to be dissolved in propylene glycol.
I also heard that it should be heated to allow the compound to fully dissolve.

Do I need to know anything else ?
What compounds are you using ?
 
Youpi said:
Don't focus on the e-cig part, I own two, one of them I can set the voltage so I'm quite set up.
I would like to know what cannabinoid is used, I guess it has to be dissolved in propylene glycol.
I also heard that it should be heated to allow the compound to fully dissolve.

Do I need to know anything else ?
What compounds are you using ?
Click to expand...
Look up tinctures specifically for e cigs online to get more info- i'm quite into vaping and have been for a while now and although i don't use THC in my vapes quite alot of people have asked how to so i've inadvertently gathered some info on the subject.

Look up tinctures- look up what's in them- go from there.
 
Well most of the tinctures I have seen were not clearly stating what cannabinoid was inside them.
Come on, I am sure someone on here did his own tincture already, I'm sure i'm not the first one to think about this, am I ?
 
Bump.

If you've ever done this, please let us know what substance you used.
 
BHO in propylene glycol. Will require gentle warming to get into solution. A little vegetable glycerin can be added if you like to blow big exhalation plumes.
 
Last edited:
I know from some german forums that ab-fubinaca und ab-chminaca work in PG via e-cig. but be careful with the dosage.
 
I'm sorry- assumed that folk would be familiar w/ the term. BHO is Butane Honey Oil, a cannabis extract made by basically rinsing cannabis in butane and then evaporating the solvent. You're left w/ a viscous liquid that greatly resembles honey. This stuff is way too thick for the wick systems that most e-cigs use, so it's thinned w/ glycol to a workable consistency.

Try doing youtube searches for "BHO" and/or "dabbing".
 
rhizome said:
BHO in propylene glycol. Will require gentle warming to get into solution. A little vegetable glycerin can be added if you like to blow big exhalation plumes.
Click to expand...

Seconding this as it works great. Another thing that works good is putting oils dabs or wax in an RDA. Thicker stuff can be put right onto the coils well wax can be put onto the cotton or on the coils.
 
rhizome said:
I'm sorry- assumed that folk would be familiar w/ the term. BHO is Butane Honey Oil, a cannabis extract made by basically rinsing cannabis in butane and then evaporating the solvent. You're left w/ a viscous liquid that greatly resembles honey. This stuff is way too thick for the wick systems that most e-cigs use, so it's thinned w/ glycol to a workable consistency.

Try doing youtube searches for "BHO" and/or "dabbing".
Click to expand...
Why don't you say so? :D Made that dozens of times. Very interesting indeed.

varg said:
I know from some german forums that ab-fubinaca und ab-chminaca work in PG via e-cig. but be careful with the dosage.
Click to expand...
Thank you very much, problem solved.
 
All of them are soluble in PG and vaporize just fine, as far as I know.
 
There are now two kinds of e-cigs. One is a vaporizer and another one an 'atomizer' designed specifically for oils and waxes.

The manufacturers want to capture the pot , crack and meth markets.

The vaping is for liquid nicotine and meth can also be vaporized. However , crystal comes in solid form and I dont know how long it would take to melt but I am certain you can transform it into liquid form.

I have tried high and low to find a formula to make liquid THC but it just doesnt work that way. You get an oil based product so you need the atomizer which burns oil and crack , not vaporizes it. In other words, you can stick actual weed into it and it would burn it just like burning a joint.

I went and purchased a itaste exgo 2.0 battery with a vaporizer tank. The battery and variable voltage is awesome. I then went and got a yocan w3 atomizer tank with nero technology that fits on the itaste battery so i can burn waxes and oils.

It has no coils. It has a full strip of thin metal that heats up to 1300 degrees within 1 second. Easily enough to burn anything you put in there.
 
You must log in or register to reply here.
Top