Anyone one who knows about "Enhanced Leaf" DMT infusion method please help!

[DubbyKid]

I was wondering if this would work
put some isopropyl in a shotglass
put desired amount of dmt mix around
put parsley/mint etc...
wait a few days?
do i now have a smokable form of DMT?

 

[kingpin106]

just wait until the iso is evapped, smoke and enjoy

 

[Solipsis]

Sounds good but what I always wonder is if you don't end up with a lot of DMT sticking to your shotglass because on a small scale the surface is not that well covered with plant material...
I guess that it would help to chop up your plant material (e.g. leaves) very well, but if do it too well it might not sit as neatly in your vaporizing device and more plant material means more volume for the DMT to vape from and less burning.

 

[The Hebrew Hammer]

I would use acetone and caapi leaf instead , thus making Changa rather than enhanced leaf, much more bang for your buck.

 

[villian]

Sounds good but what I always wonder is if you don't end up with a lot of DMT sticking to your shotglass because on a small scale the surface is not that well covered with plant material...
I guess that it would help to chop up your plant material (e.g. leaves) very well, but if do it too well it might not sit as neatly in your vaporizing device and more plant material means more volume for the DMT to vape from and less burning.

There will be some DMT stuck on the glass still but after the solvent is done evaporating you can just rub up the excess DMT with the leaf like a sponge.. it comes right off.

 

[DubbyKid]

thanks so much everyone

 

[pharmakos]

the way i always dreamed of it...

1. measure out an amount of DMT
2. dissolve it in a known amount of alcohol
3. roll up herbal joints
4. use a dropper to carefully drop a measured dose of DMT onto each joint

you could even get some Rue extract involved

 

[The Hebrew Hammer]

3. roll up herbal joints
4. use a dropper to carefully drop a measured dose of DMT onto each joint

This is not really ideal.

I mean, why drop drops onto already rolled joints, Its much more easy and practical if you measure out say 1 gram of DMT and 1 gram of caapi leaf, then you know that you have 2 grams of 50%DMT so in other words, if you want a break through dose of say 50mg or so, you smoke 100mg of material.

And of course, if you want it in a joint, you simply mix the 100mg of material (containing 50mg of DMT) with whatever herb you want to mix it with as you roll the joint, you still know what dose your getting because you simply know that the mix is 50%/50% (before adding other herbs / weed to fill the joint)

As for the shotglass collecting DMT on its sides, I use something more like a dish than a shot glass, but the technique goes through to any vessel. When you get down to the end of drying it simply continue mixing the plant material every few minutes or so until its dry. this way it keeps pretty much all the DMT in the plant material, of course there is left over residue on the shot glass, but its not like milligram upon milligram.

I would like to note at this time that While its incredibly fun to smoke joints of changa, its incredibly wasteful and the experience is far from the same experience if you smoke your dose all in one hit (or really quickly in general) like when smoking FB spice.

 

[adrian89987]

There will be some DMT stuck on the glass still but after the solvent is done evaporating you can just rub up the excess DMT with the leaf like a sponge.. it comes right off.

Precisely how I deal with that.


That procedure sounds fine for making enhanced leaf. If you can get it I highly recommend using some mullein as your carrier herb.

 

[any major dude]

here's a link to the Big & Dandy Changa Thread. There should be some useful info there

 

[pharmakos]

I mean, why drop drops onto already rolled joints, Its much more easy and practical if you measure out say 1 gram of DMT and 1 gram of caapi leaf, then you know that you have 2 grams of 50%DMT so in other words, if you want a break through dose of say 50mg or so, you smoke 100mg of material.

how do you ensure that the DMT is evenly dispersed in the carrier herb?