Opioids ideal ratio of water to medication

[dmcheatw]

i want to make a solution of oxycodone for injection. what is the best ratio of water to mg of oxycodone? in other words, how much oxycodone (in mg) can one ml of water absorb? the pills are 5mg each.

 

[187coopa]

go shoot something thats worth it thats a start

i dont condone needle use outside of a hospital enviroment.

 

[Captain.Heroin]

If you aren't micron filtering, you're not going to be able to fit a whole lot in 1 CC. So don't bother.

If you can micron filter, then you should be able to fit a relatively decent amount in per CC.

 

[hedon]

you need pills the dont have apap (oxycodone 30) or even 15s would be the lowest dose of oxycodone i would shoot, but to answer your question it doesnt matter how much water, i use as much water as possible to make sure i get as much of the oxycodone out of the mixture as possible, i use cotton though (not recomended) if your trying to shoot 5mg percs, and are asking how much water to use it sounds liikke you know way to little to attempt iv yourself....

 

[dmcheatw]

go shoot something thats worth it thats a start

i dont condone needle use outside of a hospital enviroment.

if you do everything properly, there is little difference between being injected in a hospital vs doing it at home.

can a nurse who comes to your house do injections? what about a medic in the field? what about an institution in a third world country?

why would you post such a worthless answer? why would you think anyone cares what you condone?

 

[dmcheatw]

they are straight oxycodone. and I am micron filtering this time around

hedon I don't understand what is different between one 15mg pill and three 5 mg pills? i see what your saying with using as much water as possible, but then i don't want to over-do it either by injecting like 5ml per pill

CH (or anyone else) can you quantify the amount of oxycodone that is soluable in 1ml of water? i appreciate the answer but a relatively decent amount is kinda vauge. i have 20 ml vials and am curious as to how many 5 mg pills I should try to dissolve in 20 ml of bac. water.

 

[Dankycodone]

^ There is way more binders way more fillers. if you are gonna do it no matter what first CWE it then filter thorugh a cotton then micron filter it and its still not recommended though. Oxycodone is soluble in water at 100mg per ml.

 

[dmcheatw]

thanks danky. I googled it and found several competing answers (and some unresolved threads on bluelight) one source says 100mg/ml another says "5.59e+00 mg/mL" (http://www.drugbank.ca/drugs/DB00497). also, nobody mentions what temperature the water is, which i would think does matter...

i'm planning to cotton pre-filter that way I can save the powder and ingest it orally. very good advice

I'm certainly no expert, but I'm not sure I need to CWE if there isn't any over the counter pain medication coupled with it right?

also, if there is only 10 more mg of active ingredient in a 15mg oxycodone vs a 5mg oxycodone, then that only amounts to 10mg less filler/binders for an equal sized pill correct? there is definately more filler/binders, but at a glance it wouldn't seem like it was that much difference. again someone correct me if i'm wrong because as i said i'm certainly no expert.

 

[Dankycodone]

thanks danky. I googled it and found several competing answers (and some unresolved threads on bluelight) one source says 100mg/ml another says "5.59e+00 mg/mL" (http://www.drugbank.ca/drugs/DB00497). also, nobody mentions what temperature the water is, which i would think does matter...

i'm planning to cotton pre-filter that way I can save the powder and ingest it orally. very good advice

I'm certainly no expert, but I'm not sure I need to CWE if there isn't any over the counter pain medication coupled with it right?

also, if there is only 10 more mg of active ingredient in a 15mg oxycodone vs a 5mg oxycodone, then that only amounts to 10mg less filler/binders for an equal sized pill correct? there is definately more filler/binders, but at a glance it wouldn't seem like it was that much difference. again someone correct me if i'm wrong because as i said i'm certainly no expert.

No problem dude. How much binders and fillers a pill has totally depends on the size of the pill the bigger the more fillers it has. So obviously it's better to shoot one 15mg pill vs 3 5mg pills. No need to cwe if it is not compounded. Oxycodone is highly Soluble In cold water.

 

[fredPA]

I have shot those little 5mg Roxies(M, 0552), I was using 1cc for 2 pills and as you can imagine, repeating over and over again.

Its not worth doing it, but obviously you aint trying to hear it. Good luck


I have heard people call them percolones too.

 

[dmcheatw]

yeah i i can see that 1 pill vs 3 pills is a LOT more filler actually. i didn't look at it that way at first. oh well that just means it will take more work to isolate the oxycodone. i think i'll put 40 pills in 20ml water, which would be 10ml oxy per shot.

i can appreciate that it isn't worth doing to a lot of people, but you are right fred i'm not trying to hear it .

 

[dmcheatw]

okay i'm actually going to put 60 pills in 20 ml of water, that way i can work my way up to a 15mg dose in my 1ml/cc syringes.

can anyone estimate how many ml of water i should start with for dissolving 60 generic oxycodone pills if i want an end result of 20 ml of water? i plan to presoak the cotton, so the question is how much water will 60 pills retain on their own i'll be using a syringe so i can really squeeze as much water out of the residual powder as possible?

seems like i remember when doing 1 pill it would retain 10-20 units (1/10th or 1/5th of a cc/ml) so i'm thinking i should start with somewhere between 26ml and 32ml water...?

 

[affasd]

when I shot the 15 mg roxies I would put in an extra 20 units and would end up with a full 1 ml syringe, that was with like 2 or 3 of the pills usually. I dunno how it would be with 5's tho especially if your using 60 of them

 

[dmcheatw]

thanks mate!