Laying 5-MeO-MIPT

[HeroinBob]

Hi,

My friend recently came into 1g/1000mg's of 5-MeO-MIPT.

He doesn't like the fact of putting in capsules but has spare blotter sheets around, and was wondering how he would go about going from 1000mg's of crystal to dosages of about 3mg per millimeter, he will be using everclear or acetone to dissolve the crystals, i would just like to say rite now that he is looking to use these blotters for his own personal research.

He was also wondering if there is any way to possibly dose 2-3 sheets (200-300)
1/4" or 3/8" with each hit having a does of 3-5mgs.

Any help or information that i would be able to tell my friend to help him out would be amazing and would be greatly appreciated.

I would also like to state again that this is for his own person research.

Thanks.

Also if this thread is in anyway going against any of the rules and or in the wrong forum i would be great if someone could let me know as i have posted a thread here before.

 

[danceofdays]

I think the most you're gonna be able to fit in each 5mm by 5mm square would be along the lines of 1 or 2mg.

 

[fryingsquirrel]

Yeah, 5meo-mipt isn't really potent enough to place on blotter. And that is usually done with the intent of passing something off as LSD, which isn't a practice anyone should condone.

 

[psykoman]

u can mix it with alcohol sumthing like ethanol because this will evaporate off the sheet leaving onnly the active substance - u will have to work out how much liquid ure blotting paper holds with a few trial and error and then use simple maths to work out how much each blotter will end up with it on it.

i kno how to do it i layed 2cb onto big inch square blotters and DOM onto normal ones. i cant really be arsed typing out the hole procedure but if ure really stuck mate PM me.

most people looking to do this tho are looking to sell there stuff as LSD as it will sell alot easyer than explaining to people not in the know exactly what it is in ure capsule - and if its for the guys own use why is he wanting to go to all this bother when he can just cap it or put the dose in a skin?? (i layed these chemicals as it was easier to take about with me in blotter form as i was selling lots of it and i could stash it easier than a big bag of capsules when moving from party to party plus the fact most people like the look of blotters was a good marketing tech and i always sold it as what it was) also its possible if u don't lay it right that sum tabs will be higher doses than the rest so from a personal research use this is no use at all and don't really believe that hed want to do this for his own use. he might have the same reasons as me for wanting to do it or he might have too much time on his hands but its more than likly to sell as LSD. so from a harm reduction point of view I would tell you to capsule it up using a mg scale so your research is always accurate. But if he is selling it and sells it for what it is and to make it a more funky looking product ill help you.

of course a simple google search will give u this information also.

 

[HeroinBob]

Hi, thanks for the reply's im well aware that it's a bit sketchy for him wating to put it on blotter but he s not a dealer and never has been, at the moment he only has blotter sheets and has the 5meo-mipt and would rather not wait another 2 weeks to order some capsules then just have a little bag of powder pills on his person, and hes pretty anti-pill since he has lost a few people oxys and the like so i honestly don't blame him. and the people we know are just not stupid enough to be able to pass this of as real LSD not to mention that it would be just morally wrong to scam someone like that and give them a substance that they do not know about, regardless of the dose that's why i was trying to emphasize that he is using this for personal use's and not for being retarded and passing blotter off as something its not.

I'm well aware and he and i have researched enough to know that a 1/4" blotter can hold about 2-4mg and a 3/'8 for hold about 5-6mg i know that 5meo-mipt i orally active at

Threshold 1 - 2 mg
Light 2 - 4 mg
Common 4 - 6 mg
Strong 5 - 12 mg
Heavy 15+ mg

all he really would like to know is:

1. Is this possible
2. be solvent to use
3.best process to go through i dont need major details unless you are able to tell me how many mls/ per mg i should use to get the proper dilution/conversion of the crystals.

Also iv'e been reading extensively about Alot of people being able to put 4-5mg's on blotter using AMT,2C-t-7,2C-t-2,2C-D,4-aco-dmt,4-Acetoxy-DIPT, etc. and out of all of these the oral dose of 5-meo-mipt is the lowest dosage while going up to the heavier doses of 15mgs.
while a heavy dose of 2C-i would be about 25-40 orally so in all consideration this should be able to work shouldn't it???

And again i would like to state that THIS IS FOR PERSONAL/RESEARCH PURPOSES ONLY, This is NOT in any way,shape or form about selling something on blotter that is not LSD and anyone who would think this is either kinda of retarded or brain-dead for even mentioning something as stupid as that.

Thanks for everyone's help so far and have a great day.

Jon.

 

[HeroinBob]

u can mix it with alcohol sumthing like ethanol because this will evaporate off the sheet leaving onnly the active substance - u will have to work out how much liquid ure blotting paper holds with a few trial and error and then use simple maths to work out how much each blotter will end up with it on it.

Hi,

I am aware the i need to use alcohol to dissolve the crystals, I know how to do the whole process myself and that why i happened to mention the everclear and acetone ive herd that these would give more concentration to the solution where less liquid is needed to dissolve the crystals.

How ever all that is really needed to know is an approximate formula or solution that would allow me to get about even 3-4mgs on each piece of blotter paper whether it be the 1/4" blotter or the 3/8"blotters.

i have all supplies needed for the process

syringe
ml dropper
mg scales
solvent (everclear,ethanol,acetone)
blotter paper (1/4" & 3/8")
several Pyrex dishes and mixing containers.

The only thing i need to know now if this is even possible/worth the time ( and the concentration(ML) of solvent i would need to dissolve the crystal so i can obtain the desired amount of 2-4mgs per hit.

Thanks again.

 

[HeroinBob]

My friend is also an experienced "Lab Rat"/"Guinea Pig". He has tried to many types of these chemicals as i have only tried about 8-10 different research substances. so all in all between me and him we also knows the proper doses and precautionary measures to assure his/my safety while experimenting.