Opioids Just banged 2x 30mg of Generic Oxycodone

[BackSeatSuicide]

So i finally got a chance to try a decent amount of oxy, using the IV ROA, i tried it for the first time last night but it was only 1x 30mg, so it wasn't quite enough for my current tolerance. I did it after slamming 2x 60mg MScontins, but barely felt it, it did add to the morphine high, but i was expecting a lil more. From what I am told, there's really not much of a rush from Oxycodone/contin, but that it has a really nice high, and finally I feel that. But anyways, on to my question.....

Whats the best process for prepping these 15mg and 30mg Oxycodone IR? those are the two kind i get, usually they are the white ones that say either 15 or 30 on one side and have a M inside a square on the other, and have a score line on the side with the number on it. Tho sometimes i get the all green 15's and the all blue 30's, just depends on who and where i get them, but I do prefer the white ones with the M on the back, cause they are better for snorting, and they seem to work a lot better then the other brands I've gotten. So what I've been doing to prep them is; I crush them up (which i heard you didn't even need to do, but i think it makes it dissolve easier) put a full 1cc syringe of water in the spoon, heat it up til it starts to bubble (i heard from some people that you do need the water to be warm, cause it helps make it more soluble, and I've heard that you dont have to, but either way i prefer to heat the water a lil anyways, cause it gets any bacteria out of teh water, I am a really really clean person, which is a good thing, especially when it comes to IV Drug use) so after heating it up a lil, i drop the powder into the water, and stir it up for a couple minutes. Then i drop my cotton in there and suck that bitch up. After I stir it up, there still is powder in the water, but from what I'm told, thats just the binder/filler that is left, but when i drop the cotton in there and suck it up, the fluid that is left in the syringe is crystal clear. So does this sound like the best way to do it, or does anyone have a better more efficient way to prep these oxycodones ?

 

[cozycompany]

hey man,

First its not good to heat your pills. I dont believe there is any pill you want to heat up (maybe except for dilaudid, but just a little heat for the wax) because the binders and fillers will melt into the liquid that you inject. Someone please correct this if im wrong. other than that it sounds like your going through the right steps to iv. are you using alcohol to wipe down the injection site? i also put antibacterial jell on the site after i bang...just a thought

 

[rob007]

i am not a needle fanatic but as far as i know, banging pills are no good. especially if you dont have a micon filter.

 

[rocknroll702]

dayumm i know people that have died from shooting up legit ocs prior to the formulation change.. to use generics id be very careful and be prepared to throw up!

 

[effie]

Don't bump your own threads, someone will reply eventually! BL isn't an emergency response service

You should never heat pills - the idea that it kills bacteria is false, water needs to be heated to around 120 degrees C for 15 minutes to sterilise it adequately.. oxycodone is water soluble, heating the pill only causes other bad things in the pill to dissolve too.

If you're shooting pills you really, really need to use a micron filter to remove dangerous fillers/binders. If you don't, you risk developing a lung condition called pneumoconiosis or talcosis, caused by particles from the pill entering your bloodstream and becoming lodged in your lungs.

All about micron filters..

Info on the evidence for micron filtering

What water are you using?

 

[lorne667]

Dude we have already said in another thread, NEVER, EVER, FOR ANY REASON HEAT YOUR PILLS. As Effie said, the idea your sterilizing it is ridiculous, the water would need to hard boil for that. And it doesn't mix ANY BETTER that way, actually worse. Honestly, if your gonna bother doing harm reduction, then don't heat pills when it will speed up the development of the lung conditions that Effie was talking about.

Also, you don't need a spoon, since you are NOT supposed to heat the pills. A shot glass is ideal for not wasting any. Also, a 1cc syringe full of water is overkill for one pill. I use half a cc syringes, and almost never fill them up, unless doing high oxy doses, in which case high enough doses require multiple shots, for example banging 3 30's.

 

[Captain.Heroin]

The best way is documented in the last link in my signature.

Please read through that and it will tell you essentially everything you'll need to know.

Finally, please don't bump your own post.