• Neuroscience & Pharmacology Discussion Welcome Guest
    Posting Rules Bluelight Rules
    Recent Journal Articles Chemistry Mega-Thread
    FREE Chemistry Databases! Self-Education Guide

  • N&PD Moderators: Skorpio | someguyontheinternet

From pure crystals to Blotter

A

Afterm4th

Bluelighter
Joined
Oct 3, 2006
Messages
463
What is the process that allows one to get LSD25 crystals to liquid form to blotter paper?

Is it as simple as taking the crystal LSD and combining it with H2O? If so, then what is the ratio of LSD crystal to water?

Then, is it as simple as taking blotter paper and soalking it in the aquious solution?

Is the process the same for DOx substances?
 
I'm going to hold my tongue because I'm not 100% sure whether this kind of thread violates any Bluelight rules.

But I can tell you that the answer you seek dwells over at the Shroomery forums.

Look for one of Chinacat's mega-threads. The title reads something like ¨LSD crystal to blotter.¨
 
Lay the blotting paper down on a sheet of perspex and draw around it with a permanent marker so that you have your 'template'. Using a stanley knife cut out a 'hole' around the template. Use a steel ruler if you dont wanna fuck it up. Glue a second sheet of perspex underneath the hole. It's very important that it is leak resistant.

Make sure the spirit level works exactly, both linear & sideways. You can use like playing cards on the corners to fine tune it. Dissolve the active in a generous portion of hot alcohol pour over the sheet and leave to evaporate.

^^That's quite advanced & is theoretical.

Blotting individual tabs is much more practical for personal consumption (although with lsd 1g is like 10,000 doses)
 
Last edited:
Kickass. That answers all my questions except for a few spicifics..

What is the alcohol/water ratio when making the aquious solution of LSD? Also what is the LSD to alcohol/water solution ratio?

Would a person just desolve the crystal LSD directly into 40% to 70% vodka? Or would the vodka be diluted with H2O first?

And then what's the usual ratio of Vodka solution to LSD? One gram of lsd crystal per every one leter of alcohol?

And lastly, is it the same procedure for DOx substances when putting them to blotter?

Thanks, fastandbulbous!
 
With DOB, 1g = 500 blotters so... 1g can be dissolved in like 49ml tap water in a screw-top bottle. Shake the bottle like mad to get it fully dissolved. Each drop weighs ~50mg and is a 2mg dose. Needless to say you need a dropping pipette (aka Pasteur pipette) and a steady hand. This is for the purpose of harm reduction. I dont intend you fool around with scheduled drugs as this would be illegal, and may also be harmful.
 
thats just what the world needs is more DOx floating around on blotters....

Aftermath, Ill ask you to reconsider putting DOx on blotter, its just as effective in gelcaps and people wont think is acid, unless you intend to pass it off as acid, which is WRONG
 
What is the alcohol/water ratio when making the aquious solution of LSD? Also what is the LSD to alcohol/water solution ratio?

Just use the vodka as is, probably best off using 70% alcohol by volume vodka as it'll evaporate faster. The strength of the LSD solution produced is dependant upon whic method you intend to use for applying it

Would a person just desolve the crystal LSD directly into 40% to 70% vodka? Or would the vodka be diluted with H2O first?

Straight into the vodka - that's all

And then what's the usual ratio of Vodka solution to LSD? One gram of lsd crystal per every one leter of alcohol?

The strength of the LSD solution produced is dependant upon whic method you intend to use for applying it

And lastly, is it the same procedure for DOx substances when putting them to blotter?

Probably (intentionally vague). Forget about putting DOX compounds onto blotter for the reasons mentioned above; in most cases the only reason for putting a DOX onto blotting paper is to sell it (more often than not misrepresented as LSD). For DOX, if you want a dry dilution of it for the purposes of transporting to take somewhere else, just drop a known amount (ie set volume of known strength solution) onto something like lactose or glucose and leave it for the solvent to evaporate in a warm, dry place. That way you can produce a dry powder with a known amount of the compound present (if it's thouroghly mixed after drying), such as 2mg of DOB per 500mg of glucose powder. there's no good reason why that shouldn't suffice for transportation reasons
 
You kick ass, fastandbulbous!

There's only one part of your answers I do not understand

The strength of the LSD solution produced is dependant upon whic method you intend to use for applying it
Click to expand...

Let say Im making this solution spicificly to put onto blotter paper. Lets say I have a 100 lot sheet of blotter ready to go.

How much LSD crystals to alcohol? ...also, would everclear (95% alcohol) work too? That would evaporate way faster.
 
I meant if you're going to soak a sheet or apply individual drops to eah square - obviously if you're going for the soak & dry method you'll want a more dilute solution; that's all I meant. As for specific concentrations I'm afraid it's dependant upon things like the pasper absorbancy, the size of each individual blotter, the dose you want per blotter etc. That involes trial & error on dummy runs without any LSD present; then you need to do all the associate maths to work out what volume of what strength you need.

Everclear should work (if it's just ethanol, methanol & water, but you never know if they'll add something else to prevent people drinking it that'll bugger up the LSD), but in real life I've only ever known vodka to be the preferred solvent
 
You must log in or register to reply here.
Top