Cocaine Cooking small ammounts of crack, and best homeade pipe?

[sveets]

I've used this method probably 10-15 times with varying results (i think the quality of the coke was a major factor) but maybe someone has a better method.

I usually get a gram or something first. Then these are my tools/ingredients:

metal spoon
metal butter knife
baking soda
bottled water
metal sewing needle
lighter
key or end of straw to place bumps of coke on the spoon
paper towel (for mess...)


First I put 2-3 "bumps" with my key/straw on the spoon, then I sprinkle a little baking soda (maybe 1/5 to 1/4 compared to the blow)
then, I dip my finger in the water bottle and put 3 drops on the spoon so it covers all the coke/bakingsoda but doesn't drown it completely.
then, I stir it up a bit with the metal sewing needle
next, I use my lighter (bic usually) and heat the spoon without letting the flame actually touch the spoon
the solution bubbles a bit, the water evaporates, and I'm left with an oily goo that I scrape with the metal butter knife.
repeat a couple or several times always using the same knife to collect the oily substance
let it dry on the knife for a little, then gently scrape/push off onto my homemade pipe (water bottle usually)


---

any suggestions for improving the method? (without having to buy any other ingredients/tools)

Also, I usually just use a regular water bottle with 2 holes poked in it. I put a cut straw in one hole and tape it so there are no spots for air to escape while the other hole acts as a carb. I also fill the bottle with a little water. I place the crack on a piece of foil with ash from a cig and little holes poked with the sewing needle. Light it up, and enjoy ..

---

I have pretty good coke. My new guy has much better stuff than I used to get, but this batch is cut with something that is irritating my nose and making it drip alot so I figured I would try making some crack with it to give my nose a break. The coke is good, its just cut with something my nose doesn't like. It's not the best (I've had almost pure straight from Colombia when I was in Panama) but it is pretty good.

 

[opiatekrzy]

best homeade pipe: buy one of those mini little socket wrenches at any convient store, break the socket off, u got hollow metal tube, and buy some chore!, or take tinfoil and roll into a tube, strenghten it, shove brillow in it, squeeze tinfoil against it making it air tight as possible, and ur good to go,....pop can method is a WASTE, freebasing off foil is a WASTE UNLESS U KNOW WHAT UR DOING.....crack only is awesome when used with a stem..what i do to cook crack, i take a niice CHUNK of POWDER, put inside a METAL measuring SPOON, sprinkle a fraction amt of baking soda in there, add enough water by using a needle to make it look pasty (not totally watered down and mixed) and thick loooking, apply flame under metal measuring cup, when i see it drying up and hardening up i submerge the whole measuring cup under ice water, and sprinkle crushed ice on top of the pasty formula, i let it dry by the window sill for a few mins, and i just made crack and i made it by the purity i prefer!!!

 

[Crashing]

You shouldn't be left with a goo, doesn't sound like you're actually freebasing it if you're left with an oily goo. You should be left with a stone. To get that, add the bumps of cocaine and baking soda and completely drown it in water. Then, boil the water and almost instantly if you have good coke a solid chunk of crack should precipitate. If it doesn't, add a bit more baking soda until it does. If you can't get it to rock up, it's really low quality. You shouldn't have to use small amounts of water to retain the product, if it's got cocaine in it then even in a gallon of boiling water the rock should immediately just form and float to the top.

Your water bottle pipe seems highly ineffective for smoking crack, too. The thing about crack is that it melts and evaporates then cools and precipitates again almost instantaneously, so if you're smoking it through ashes on foil you're probably losing 90% of the hit on the inside of the bottle. For a crack pipe, you need a thick screen that is traditionally used in glass tube pipes because it captures all of the resins and results in a much more effective hit. If you can't get a real straight shooter then the next best option would be a lightbulb pipe and then chasing off of foil, which doesn't allow the resin to vanish, but still won't be anywhere near as good as a traditional pipe. But Opiatecrzy's method would work well also.

 

[brutus]

This has nothing whatsoever to do with harm reduction. Please read the rules in my signature.