-
OD Moderators: Keif’ Richards | negrogesic
RCs Best way to Turn Liquid Ketemine to Powder
- Thread starter bnghit3
- Start date
Mr Blonde
Bluelighter
What is the solvent used in ketamax? Is it ethanol? If so, it should evaporate quicker then water. Ethanol has a much lower melting point then ketamine does, so you could probably use a fan or hair dryer to speed up the process. Putting it in the oven or on the stove is probably not recommended due to ethanol's flammability. If it's water though you could do that at an appropriate temperature.
If it's water, or even ethanol, what works well without exposing it to too high a temperature is using a pan of boiling water gently boiling and put a ceramic plate on top with the liquid ketamine on it. The heat from the steam will evap the liquid fairly effectively and leave you with decent crystals you can scrape off/crush up.
HdoubleODeezy
Bluelighter
that's a great idea about using the plate.. when i evap stuff with a "double boiler" method i usually put 1.5 inches of water in a pan and boil it and put what i need to evap into a shot glass and carefully place it in the water so it doesn't spill. Thanks for the new idea
.. probably works a lot faster than my method also. %)
sekio
Bluelight Crew
Microwave it. All ketamine is dissolved in water - IVing ethanol is suicide.
phatass
Bluelighter
put no more than 1 or 2mm height spread throughout a pan, heat medium heating, and once it gets solid, scrape off the pan with a credit card type card , takes about 7-8 minutes....
p.s. u probably won't want to use the pan after
p.s. u probably won't want to use the pan after
its made for injection so i really doubt its ethanol base if injecting ethanol kills you. But i will prolly use the boiling pot method with the plate on top. there is a youtube vid of some gays cooking it up in the oven. They said to preheat to 250 and let cook, but never said for how long, so i don't want to end up overcooking it and ruining it. Also so i have a 10ml bottle with 250mg in it. How many doses is this going to be. How much powder will i get, like an half gram?
Specktrail
Bluelighter
- Joined
- Aug 22, 2010
- Messages
- 94
Pour in pyrex dish ... heat with hair dryer on high.. slowly roll the liquid around whilst heating with hair dryer until crystals form. Or .... place pot of water on stove..boil.. the put a plate over top of the pot.. pour liquid ket on plate ..let it sit until crystals form..be safe have fun
sekio
Bluelight Crew
Hmm. I would hazard a guess a bottle of 250mg of ketamine would probably produce something like 250 milligrams, or a quarter gram.
If you've done dissociatives like third plateau DXM or PCP, snort half or all of it. Otherwise divide it into 5 equal piles, snort 1, and go from there.
Wesley_pipes_27
Bluelighter
Mr Blonde
Bluelighter
Ethanol doesn't kill you if injected. It's not great for your veins but it does get used sometimes in medicine as an IV solution.
You would cook it until it's almost all evaporated... but the steam bath method is probably the best way to go. I wish I'd thought of that when I posted, ha ha.
I think everything will evaporate except the ketamine, so you should have 250mg of powder afterwards.
When i had to cook down 30ml of 50mg/ml ketamine, i dumped it all into a glass plate, and popped it in the toaster oven on a really low setting (somewhere in the "keep warm" range) and it worked like a charm. Do note that when it looks dry on the top, it's not done; it's still wet underneath.
mikemikemike
Bluelighter
I'm fairly certain it is made for IM injection.
Whenever I did it, I always put the oven on 250, and poured the k into a flat glass casserole dish. I would leave it in the oven for 3-4 minutes, then I would leave the oven door open so that I culd see when it has dried. It is probably about the easiest thing to prepare next to boiling water, just don't get the heat too high. You will have a white film where you once had K liquid. Scrape it up and snoot it. Personally I would be scared to inject it, it's intense enough when snooted.