How to inject powder heroin
Ok, so of course I highly recommend you
NOT inject heroin as it's super-addictive, but if you're going to do it anyway, here are my instructions for how to inject powder heroin:
Beginner prep process when you don't have a micron filter:
1. Separate out about 0.01g heroin - if the bags you get are 0.1g then divide it into ten - you want to do just a very tiny amount for your first time (and should also be doing a this when you get a new batch or have gone a couple days without using)
2. Place heroin in a clean spoon (clean the spoon with alcohol or an alcohol swab first, let dry completely)
3. Put some sterile water in the spoon (make sure it's just a small amount, you don’t want to fill up more than 1/3 of the syringe)
4. Stir (you can stir it with the plunger from a syringe, but then you want to either clean it before using it for the syringe or else just sacrifice one syringe for a stirrer, you can also use something like an un-bent paperclip that has been cleaned with alcohol) *do not heat
5. If you don't have a micron filter place a Sterifilt, a piece cut from a clean cigarette filter, or a clean well-packed cotton into the spoon
6. Draw up your solution through the needle into the syringe through the filter
7. Clean your spoon
8. Squirt the liquid back into the spoon
9. Using a lighter under the spoon, heat the solution just until it boils
10. Let it cool
11. Place a clean filter/cotton in the spoon
12. Draw the solution up into a fresh syringe or rinse your original syringe thoroughly with water and use it (but never use a syringe that you have used for injection before, they get dull VERY fast)
13. Holding the syringe with the needle pointing up, slowly push in the plunger to squeeze any air out of the syringe
14. Inject (see procedure)
Note:
REALLY it is way better/safer to use a micron filter, you can get info and instructions in
the micron filter thread. Also if you use a micron filter and bacteriostatic water you can make enough solution at once to last you for multiple shots. People are always claiming you can’t do this with heroin, that it will convert to morphine if you leave it in water for a long time, but that actually isn’t true.
Alternatively, even if you don’t have a micron filter you can make enough for a few shots at a time, although without bacteriostatic water I wouldn’t really want to save it for more than a day. If you made enough solution for more than 1 shot, "piggy-back" enough solution for one shot into a new syringe. Take the plunger out of the new syringe and squirt however much liquid you want into it from the syringe with the solution in it. For example, if you want to do a 0.01g shot and you put 0.1g of heroin into your solution and the syringe has 100 units in it, then squirt 10 units into the new syringe. If the main syringe has a weird number of units in it or you are working with more complicated fractions, use a calculator to avoid accidentally doing the wrong amount. When piggy-backing be very careful not to accidentally squirt the solution out when you put the plunger back in.
As for the actual injection:
1. Find your best biggest vein, this should be the vein in the crook of your arm, start with the arm you don’t write with, the vein should be about 1/3 of the way in from the outside of your arm.
2. Using an alcohol swab, swab the area.
3. Insert the needle into the vein with the needle pointing in the direction of bloodflow (on the arm this would be up toward your shoulder). You want to insert it an angle:
4. Steadily holding the syringe, slowly pull up on the plunger a little to "register" by drawing blood into the vein. If no blood comes in, keep holding the plunger back and gently move the needle a bit deeper or shallower in the vein. Once you see blood enter the syringe, don’t move the needle and pull up a tiny bit more on the plunger to make sure it is still in the vein and more blood comes into the syringe.
Here is how to hold the syringe with one hand so you can draw up on the plunger:
(do a mirror image if you are using your right hand to inject into your left arm)
5. Gently and slowly start to press down the plunger. If it hurts or something feels wrong, stop immediately! and repeat step 4.
6. Finish injecting and carefully remove the needle from your arm. Apply a clean cotton ball or gauze to the area.
7. Enjoy. If after a 10 minutes you still don’t feel high then repeat the whole process with another small amount of heroin. You MUST use a fresh syringe every time and you should try to use a different vein or a different spot on the vein each time.
Other tips: You shouldn't need to use a tourniquet at first. If you do, get a proper synthetic rubber tourniquet, do not use a belt, shoelace etc. And ask me to explain how to use a tourniquet properly - you don't want to inject with the tourniquet still tied.
Let me know if you have any questions or need a picture of anything else
