^
|
I've used that method too...personally I didn't like it...But to each his own.
First let me preface this by saying that the best way to smoke meth is with, wait for it, a Meth Pipe. You can get them at any headshop for about $10.00 and they make everything so much easier...You can even smoke your Crystal going down the road!
2) How do you cut the metal top part off?
There are a few brands that the metal part actually twists off! It's not threaded or anything like that, but with a little work, you can break the metal to glass seal and it will slide right off, making for a VERY clean edge...I reccomend you get zooted *before* trying to make a smoking device out of a lightbulb...as you'll do such a better job!
3) Do u wash the insides so the white chemical is gone from the inside of the bulb?
I would ALWAYS reccomend this, especially if the bulb isn't brand new. Lemon juice salt and luke-warm water will do the trick just fine.
However, I think the reason you are asking is because you're referring to a regular white light bulb. Don't use these! Go to any home depot <and even most grocery stores> and pick up a 60 Watt CLEAR lightbulb! That's right, they make CLEAR lightbulbs...and not just the small kind. 60 watt is the ideal size IMHO. This way you don't have to worry about that pesky white paint...which is essential, as you want to be able to see the bulb filling with smoke.
4) How do u inhale? With some straw or hollow pen cap?
Either a straw (Dairy Queen and Quick Trip straws work the best...they have a larger diameter and are much stronger) or a hollow pen *TUBE*..not the cap...just take a regular $0.13 BIC pen and gut it. I'm sure you can figure the rest out from there.
5) Please elaborate with tools, methods, and ways of burning the meth.
Some people are going to disagree with me, but I think this method is the best. It LOOKS ghetto as hell but you waste much less smoke and you don't inhale metallic vapors.
First, getting that pesky metal thing off. For this method, we don't want ANY of the metal left on the bulb. If you happen to get the kind of bulb where the metal screws off, you're in luck. Just screw it off and pitch the metal. However, this particular name (the name escapes me) is tough to come by. So we'll have to improvise.
Don't try to cut it off, it never works. What you need is a flathead screw driver. (Craftsman #2 works the best). It's really quite simple. Basically put the flathead on the part of the bulb where the glass meets the metal...(it may take you a while to get it right, but in time you'll be able to do it hanging from your legs on a bar...blindfolded.)...and gently press the screwdriver head into the glass, making a small puncture in the glass..continue to do this all the way around the base of the bulb until the bulb is completely seperated from the metal...discard the metal and move on.
Turn the bulb into the regular position. (Hole towards the ceiling).
Now that you have a hole, put yer meth in the bulb.
While a butane torch works best, a regular lighter WILL work...but you'll go through more bulbs and you WILL burn the shit out of your thumb...repeatedly.
It usually takes two people with this method, but a true tweaker can always improvise.
Hold the bulb with one hand, the lighter in the other, and have the straw in your mouth. Go ahead and stick the other end of the straw in the bulb in preperation for inhalation. (
)
Start the torch (term used loosely) and move the flame to just under the part of the bulb where the meth is. Depending on the quality of your meth, it should start to change form rather quickly. For crank you may actually have to put the flame on the bulb...this isn't too much of a problem if you keep the flame moving...if you don't, you're going to get black marks on your lightbulb...most of the time they wipe off clean, but after repeated use they'll start to stain...and your bulb will get weaker.
Moving the flame around the bulb <only where the meth is, duh!> you will notice the bulb starting to fill with smoke...
Once you see you have enough to fill your lungs (You'll learn to eyeball it pretty accurately), start inhaling the smoke. Inhale as much as you can, as whatever is left over is going to seep out of the bulb...this is where the second person comes in handy, they can go ahead and take their hit; you lose less smoke this way.
Oh.. and if any of you happen to luck out and get the brand of lightbulb that actually screws off, please post it here...I get asked this question a lot and can never remember.